|
IKA - MZ-2C Chemical diaphragm pump
Oil-free chemical diaphragm pump. - Materials in contact with the medium are chemically inert
- Fast amortization if used instead of water jet pumps
- Compact
- Quiet
- Long service life Ident. No.1980500
IKA - LT 5.23 Hose adapter
For connection to the reactor vessels LR 2000.3 and LR 2000.4. Ident. No.2235000
IKA - LR 2000.90 Drip funnel
For dosing, with ground joint NS 29. For alternative also see pumps. Only for LR-2.ST and LR 2000 V.
Ident. No.2277000
IKA - VC 2 IKAVAC® Vacuum controller
Used to create a controlled partial vacuum in laboratory applications. Typical tasks are the evacuation of desiccators, vacuum apparatus, etc. Solvent recovery rates of up to 99% are possible if rotary evaporators are used. - Microprocessor-controlled
- Minimum solvent loss
- Considerable reductions in water costs
- Integrated air release valve
- Easy operation
- Space-saving stand-supported instrument
- Automatic setpoint correction
- Clearly organized membrane keyboard Ident. No.2300000
IKA - VC 2.4 Pump control
The pump control is required when using the chemical diaphragm pump MZ-2C or other electrical vacuum pumps, in conjuction with the vacuum controller VC 2. The pump is disconnected from the mains and then reconnected.
Advantage over VC 1.3: Due to the interruption of the pumps current lead, noise levels and energy costs are reduced. Ident. No.2439100
IKA - LR 2000.54 Sealing set
Spare. For LR 2000 V. Ident. No.2498900
IKA - LR 2000.80 Reactor cover
For LR 2000 V (stand LR 2000.70). Incl. 3 x NS 29 and 2 x NS 14 / 23 ground joints.
Ident. No.2508200
IKA - LR 2000.1 Reactor vessel
Double-walled, with quick-action connectors, for LR-2.ST and LR 2000 V.
Ident. No.2508300
IKA - LR 2000.10 Anchor stirrer
With PTFE scraper, for all laboratory reactors. Ident. No.2508400
IKA - LR 2000.20 Flow breaker
Only for LR 2000 V and LR-2.ST.
Ident. No.2508500
IKA - LR 2000.40 Shaft receptacle
To install the dispersing elements S 25 KV and the flow breaker LR 2000.21.
Ident. No.2509200
IKA - LR 2000.60 Sensor receptacle
To install the temperature sensors PT 100.25 and PT 100.5.
Ident. No.2509300
IKA - LR 2000.30 Vacuum gauge
Only for LR 2000 V. Alternative to the vacuum controller VC 2 IKAVAC®.
Ident. No.2509400
IKA - LR 2000.11 Anchor stirrer
With flow borings, for all laboratory reactors.
Ident. No.2509500
IKA - LR 2000.2 Reactor vessel
Double-walled, with quick-action connectors and bottom discharge valve, for LR-2.ST and LR 2000 V.
Ident. No.2509600
IKA - LR 2000.3 Reactor vessel
Double-walled for LR 2000 P (Stand LR 2000.75).
Ident. No.2509700
IKA - LR 2000.53 Stand lower set
To raise the laboratory reactor vessels LR 2000.2 and LR 2000.4. Only in connection with LR 2000.70 and LR 2000.75.
Ident. No.2509800
IKA - LR 2000.21 Flow breaker
Only for LR 2000 P in connection with LR 2000.40.
Ident. No.2571200
IKA - LT 5.24 Hose adapter
For connection to the reactor vessels LR 2000.1 and LR 2000.2.
Ident. No.2578100
IKA - LR 2000.85 Reactor cover
For LR 2000 P (stand LR 2000.75).
Ident. No.2598100
IKA - HBR 4 digital Heating bath
The digital heating bath is characterized by the following features:
- Cylindrical bath shape
- High-grade recyclable materials
- The heating elements are situated underneath the bath vessel
- Either low viscosity oil or water can be used as the heat transfer fluid
- Useful volume of 4 liters
- Heat output 1,000 W
- Adjustable safety temperature limiter acc. to DIN 12876
- The safety elements are checked when the unit is switched on
- Double jacket and carrying handles provide protection against burns
- Digital display presents rated, actual and safety temperature as well as speed
- Fuzzy logic control
- Integrated magnetic stirring drive to circulate the tempering fluid, which contributes to improved heat distribution
- Heat output 1000 W
- Heating temperature min. room temp. °C
- Heating temperature max. 200 °C
- Heat control stepless
- Controller oscillation (3 l water / 90 °C) 1 ±K
- Controller oscillation (3 l Marlotherm oil / 150 °C) 2 ±K
- Speed display LCD
- Speed control stepless
- Speed min. 100 1/min
- Speed max. 800 1/min
- Motor rating input 5 W
- Motor rating output 1 W
- Bath volume max. 5 l
- Filling point min. 20 mm
- Material in contact with medium stainless steel 1.4301
- Adjustable safety circuit min. 50 °C
- Adjustable safety circuit max. 210 °C
- Safety class DIN 12877 II
- Outer diameter 250 mm
- Inner diameter 200 mm
- Outer height 250 mm
- Inner height 160 mm
- Width 340 mm
- Depth 340 mm
- Height 250 mm
- Weight 4.4 kg
- Permissible ambient temperature max. 40 °C
- Permissible relative moisture 80 %
- Protection class according to DIN EN 60529 IP 21
- Voltage 230 V
- Frequency 50/60 Hz
- Power input 1020 W
Ident. No.2602300
IKA - LT 5.20 Hose
Coated metall hoses for circulation thermostat LT 6 control. Package contains 2 hoses.
Ident. No.2606700
IKA - PC 1.2 Adapter
Ident. No.2616800
IKA - LR 2000.57 Sealing set
Spare. For LR 2000 P.
Ident. No.2661200
IKA - PC 2.2 Adapter
Ident. No.2753200
IKA - PC 1.5 Cable
Ident. No.2756000
IKA - LR 2000.VK Attachment kit
For LR 2000 V and LR 2000 P.
Ident. No.2984600
IKA - LT 6 control Circulation thermostat
Programmable thermostat for sophisticated tempering tasks up to 300 °C.
- Temperature manually adjustable or controllable via PC
- Automatic adaption of control parameters to all temperature control tasks via PID control
- Suitable for technical procedure experiments, e.g. with lab reactors or kneaders
- Direct temperature control in external vessels is possible
- 2 x 1 m Viton hose (Ø = 10 mm, max. temperature 180 °C), included with delivery
- Appliance type circulation thermostat
- Identification according to DIN 12876 FL
- Heat output 2000 W
- Operating temperature min. 60 °C
- Operating temperature max. 300 °C
- Working temperature max. 300 °C
- Working temperature min. (with water cooling) 20 °C
- Working temperature max. (with water cooling) 300 °C
- Temperature display yes
- Connection for ext. temperature sensor PT 100
- Heat control accuracy 0.01 ±K
- Adjustable safety circuit min. 20 °C
- Adjustable safety circuit max. 300 °C
- Pump pressure max. (0 liters discharge flow) 0.5 bar
- Pump pressure max. (0 bar back pressure) 18 l/min
- Width 230 mm
- Depth 365 mm
- Height 405 mm
- Weight 18 kg
- Permissible ambient temperature min. 5 °C
- Permissible ambient temperature max. 40 °C
- Permissible relative moisture 80 %
- Protection class according to DIN EN 60529 IP 21
- RS 232 interface yes
- Analog output yes
- Voltage 230 V
- Frequency 50/60 Hz
Ident. No.3036100
IKA - PC 2.3 Cable
Ident. No.3036200
IKA - LR 2000.4 Reactor vessel
Double-walled with bottom outlet valve, for LR 2000 P (Stand LR 2000.75).
Ident. No.3064900
IKA - LR 2.1 Reactor vessel
Single-walled, for LR-2.ST.
Ident. No.3070000
IKA - DTM 12 IKATRON® Digital temperature measuring instrument
For measuring temperatures between -200 °C up to +400 °C.
- LED display
- Analog output (1 °C = 1mV)
- Almemo interface for PC connection
- Sensor connection: Almemo
- pH electrode available as accessory
- Other measuring parameters, e.g. conductivity on request
Ident. No.3113200
IKA - PT 100.25 Temperature sensor
e.g. for use with IKA® laboratory reactors in combination with sensor receptacle LR 2000.60.
Ident. No.3122300
IKA - PH 225.1 pH electrode
With temperature sensor.
Ident. No.3122600
IKA - DTM 12.15 Adapter cable pH
For connection of the pH electrode to the temperature measuring instrument DTM 12.
Ident. No.3128300
IKA - DTM 12.16
Buffer solutions pH 4 and pH 7.
Ident. No.3128400
IKA - LR 2000.65 Receptacle for pH electrode
Ident. No.3172600
IKA - VM 600 basic visco module
Torque measurement instrument for LR-2.ST, consisting of adapter kit and VK 600 control VISCOKLICK®.
Ident. No.8016600
IKA - PCI 8.2 Plug-in card
For mounting in the PC to connect up to 8 instruments simultaneously. Plug-in cards for up to 64 instruments available on request.
Ident. No.8017500
IKA - S 25 KV - 18 G Dispersing element
The variety of media to be processed also requires a variety of rotor-stator configurations and seals. In many cases it is neccessary to use subsequently two dispersing elements, for pre-crushing and fine crushing. The plug-in connectors facilitate the exchange of the dispersing elements.
- Volume range min. (H2O) 0.01 l
- Volume range max. (H2O) 1.5 l
- Stator diameter 18 mm
- Rotor diameter 12.7 mm
- Gap between rotor and stator 0.3 mm
- Circumferential speed max. 15.9 m/s
- Immersion depth min. 40 mm
- Immersion depth max. 225 mm
- Shaft length 270 mm
- Material in contact with medium FFPM / SIC, AISI 316L
- pH min. 2
- pH max. 13
- Suitable for solvents yes
- Suitable for abrasive substances no
- Working temperature max. 220 °C
- Sterilization methods wet chemical
- Vacuum 1 mbar
- Pressure max. 6 bar
- Ultimate fineness, suspensions min. 10 µm
- Ultimate fineness, suspensions max. 50 µm
- Ultimate fineness, emulsions min. 1 µm
- Ultimate fineness, emulsions max. 10 µm
Ident. No.2348000
IKA - S 25 KV - 25 G Dispersing element
The variety of media to be processed also requires a variety of rotor-stator configurations and seals. In many cases it is neccessary to use subsequently two dispersing elements, for pre-crushing and fine crushing. The plug-in connectors facilitate the exchange of the dispersing elements. - Volume range min. (H2O) 0.05 l
- Volume range max. (H2O) 2 l
- Stator diameter 25 mm
- Rotor diameter 17 mm
- Gap between rotor and stator 0.5 mm
- Circumferential speed max. 21.4 m/s
- Immersion depth min. 40 mm
- Immersion depth max. 225 mm
- Shaft length 270 mm
- Material in contact with medium FFPM / SIC, AISI 316L
- pH min. 2
- pH max. 13
- Suitable for solvents yes
- Suitable for abrasive substances no
- Working temperature max. 220 °C
- Sterilization methods wet chemical
- Vacuum 1 mbar
- Pressure max. 6 bar
- Ultimate fineness, suspensions min. 15 µm
- Ultimate fineness, suspensions max. 50 µm
- Ultimate fineness, emulsions min. 1 µm
- Ultimate fineness, emulsions max. 10 µm
Ident. No.2466900
IKA - S 25 KV - 25 F Dispersing element
The variety of media to be processed also requires a variety of rotor-stator configurations and seals. In many cases it is neccessary to use subsequently two dispersing elements, for pre-crushing and fine crushing. The plug-in connectors facilitate the exchange of the dispersing elements. - Volume range min. (H2O) 0.1 l
- Volume range max. (H2O) 2 l
- Stator diameter 25 mm
- Rotor diameter 18 mm
- Gap between rotor and stator 0.5 mm
- Circumferential speed max. 22.6 m/s
- Immersion depth min. 40 mm
- Immersion depth max. 225 mm
- Shaft length 270 mm
- Material in contact with medium FFPM / SIC, AISI 316L
- pH min. 2
- pH max. 13
- Suitable for solvents yes
- Suitable for abrasive substances no
- Working temperature max. 220 °C
- Sterilization methods wet chemical
- Vacuum 1 mbar
- Pressure max. 6 bar
- Ultimate fineness, suspensions min. 5 µm
- Ultimate fineness, suspensions max. 25 µm
- Ultimate fineness, emulsions min. 1 µm
- Ultimate fineness, emulsions max. 5 µm
Ident. No.2404000
IKA - EUROSTAR power control-visc P7
Laboratory stirrer with a high torque, 7-fold transmission reduction for processing highly viscous media.
- Constant speed by microprocessor control
- Digital display presents rated - / actual speed
- Infinitely adjustable without gear shifting
- Slim casing
- Quiet operation
- Safety circuit
- Non-locking, overload capabilities
- Enhanced safety as a result of smooth start
- Integrated torque trend display for viscosity control
- Analog interface for recording speed and torque
- RS 232 interface
- Agitator shafts are not push-through
- Stirring quantity max. (H2O) 40 l
- Motor rating input 130 W
- Motor rating output 110 W
- Speed display LCD
- Speed min. 8 1/min
- Speed max. 290 1/min
- Viscosity max. 150000 mPas
- Output max. at stirring shaft 95 W
- Permissible ON time 100 %
- Torque max. at stirring shaft 380 Ncm
- Torque max. at stirring shaft at 60 1/min (overload) 380 Ncm
- Torque max. at stirring shaft at 100 1/min 380 Ncm
- Torque max. at stirring shaft at 1.000 1/min 380 Ncm
- Speed control stepless
- Stirring element fastening chuck
- Chuck range min. diameter 0.5 mm
- Chuck range max. diameter 10 mm
- Hollow shaft (push-through ¿ when stopped) none
- Fastening on stand extension arm
- Extension arm diameter 16 mm
- Extension arm length 200 mm
- Torque display yes
- Nominal torque 3.8 Nm
- Torque measurement trend
- Width 80 mm
- Depth 190 mm
- Height 330 mm
- Weight 4.9 kg
- Permissible ambient temperature min. 5 °C
- Permissible ambient temperature max. 40 °C
- Permissible relative moisture 80 %
- Protection class according to DIN EN 60529 IP 42
- RS 232 interface yes
- Analog output yes
- Voltage 230 V
- Frequency 50/60 Hz
- Power input 130 W
Ident. No.2850700
IKA - VK 600 control VISCOKLICK® Torque measurement instrument
Rheological material properties such as viscosity, flow and deformation behavior are among the most important characteristics of any material:
- They determine the application-technical manufacturing process of a product
- The structural composititon of a material can be established from its viscosity behavior
- The sequence of chemical reactions can be documented
The VK 600 control can be combined with all IKA® EUROSTAR overhead stirrers. The appropriate stirrer is ¿clicked¿ into the VK 600 control. During stirring, a force transducer determines a reaction force at the stirring shaft proportional to the torque.
- Simple assembly
- RS 232 interface and analog output
- PC-contollable with labworldsoft®
- Measuring system is overload-proof
- Offset correction to eliminate errors
Ident. No.8015700
IKA - T 25 basic ULTRA-TURRAX®
High-performance dispersing instrument for volumes from 1 - 2,000 ml (H2O). The spectrum of applications ranges from homogenizing waste water samples to the use in laboratory reactors, to dispersion tasks under vacuum / pressure and sample preparation in medical diagnostics.
- Three types of shaft bearings
- As standard, the T 25 basic is equipped with a connection for a revolution counter
- Rotor-Stator configurations have thirty years of proven, guaranteed comparability of test results
- Wide range of dispersing elements (not included with delivery)
- Motor rating input 500 W
- Motor rating output 300 W
- Volume range min. (H2O) 0.001 l
- Volume range max. (H2O) 2 l
- Viscosity max. 5000 mPas
- Speed min. 6500 1/min
- Speed max. 24000 1/min
- Speed deviation 1 %
- Speed display scale
- Speed control stepless
- Noise without element 73 dB(A)
- Extension arm diameter 13 mm
- Extension arm length 175 mm
- Process type batch
- Width 65 mm
- Depth 80 mm
- Height 240 mm
- Weight 1.6 kg
- Permissible ambient temperature min. 5 °C
- Permissible ambient temperature max. 40 °C
- Permissible relative moisture 80 %
- Protection class according to DIN EN 60529 IP 20
- RS 232 interface no
- Analog output no
- Voltage 230 V
- Frequency 50/60 Hz
- Power input 500 W
Ident. No.2953000
IKA - DZM Control Revolution counter
Connection of an opto-electronic sensor enables measurement of the speed of rotating shafts from 0 - 50,000 rpm.
The signals received are displayed on the monitor. This enables all IKA overhead stirrers and dispersing instruments to be retrofitted with a speed display, thereby allowing reproducible work. An RS 232 interface allows the values to be recorded digital on a PC. An analog output signal for a recorder is also available. The monitor can be used as a table-top device or mounted on a stand rod.
Ident. No.8014200
IKA - labworldsoft®
Eases life in the laboratory. With this laboratory software, you can network up to 64 laboratory devices simultaneously via one PC. That makes the automation of your laboratory experiments and processes possible.
Measurements and processes may be run independently from one another. This helps to avoid long waits and you increase your productivity. The communication between PC and laboratory device is performed via the serial interface RS 232 (COM1 or COM2). With the help of plug-in cards and Ethernet RS 232 servers, up to 64 laboratory devices can be used simultaneously via one PC. All laboratory instruments can be controlled independently from each other and the measured values (speed, temperature, torque, pH, etc.) can be documented separately.
Hard- and software requirements:
Pentium 90 with at least 16 MB RAM, and a mouse. VGA display: monochrome with at least 16 levels of grey or color.
Windows 95/98/2000/NT/ME/XP... Networking, monitoring
With labworldsoft® you can network up to 64 laboratory instruments simultaneously via one PC. From sample preparation to synthesis, all steps of research and development in the lab can be automated using labworldsoft®.
Controlling
Desired temperature and speed sequences can be precisely controlled by means of freely selectable ramp functions. The ramp functions can be graphically generated, stored, and then loaded again at any time.
Recording, evaluating
labworldsoft® enables a fast and easy recording of many physical parameters which are required in the laboratory, such as pH, conductivity, temperature, torque, weight, pump rates etc.
Exporting
Data acquired in labworldsoft® can be exported into standard applications. For example it is possible to measure the speed during a test, save the data in a standard format (.txt or ASCII) and analyze in any chart calculation, i.e. Excel.
Storing / reproducing measured data
Do your test arrangements repeat themselves? With labworldsoft® all test arrangements can be stored. The stored data is available to reproduce the test, at a mouse click. The reproductability of tests is warranted within the scope of ISO 9000 and within GLP.
Documentation
For documentation purposes, all measuring results as well as the measurement
flowcharts can be printed or plotted according to GLP, ISO and QA.
Downloads:
- Your free trial version (30 days fully functional)
- labworldsoft® manual (PDF)
- Accessories description (PDF)
- Article: "Measuring, Controlling and Regulating with labworldsoft®",K.-O. Linde (PDF)
- Windows 95 yes
- Windows 98 yes
- Windows ME yes
- Windows NT4 yes
- Windows 2000 yes
- Windows XP yes
Ident. No.2970000
|
RSS Feed